Carnot heat engine

From Free net encyclopedia

(Redirected from Carnot cycle)

Template:Thermodynamic cycles The Carnot cycle is a particular thermodynamic cycle studied by Nicolas Léonard Sadi Carnot in the 1820s and expanded upon by Benoit Paul Émile Clapeyron in the 1830s and 40s.

Every thermodynamic system exists in a particular state. A thermodynamic cycle occurs when a system is taken through a series of different states, and finally returned to its initial state. In the process of going through this cycle, the system may perform work on its surroundings, thereby acting as a heat engine.

A heat engine acts by transferring energy from a warm region to a cool region of space and, in the process, converting some of that energy to mechanical work. The cycle may also be reversed. The system may be worked upon by an external force, and in the process, it can transfer thermal energy from a cooler system to a warmer one, thereby acting as a refrigerator rather than a heat engine.

The Carnot cycle is a special type of thermodynamic cycle. It is special because it is the most efficient cycle possible for converting a given amount of thermal energy into work or, conversely, for using a given amount of work for refrigeration purposes.

1 The Carnot cycle
2 Properties and significance
3 References
4 External links

[edit]

The Carnot cycle

Image:CarnotCycle1.png

The Carnot cycle when acting as a heat engine consists of the following steps:

Reversible isothermal expansion of the gas at the "hot" temperature, T_H( Isothermal heat addition ). During this step (A to B on diagram) the expanding gas causes the piston to do work on the surroundings. The gas expansion is propelled by absorption of heat from the high temperature reservoir.
Reversible adiabatic expansion of the gas. For this step (B to C on diagram) we assume the piston and cylinder are thermally insulated, so that no heat is gained or lost. The gas continues to expand, doing work on the surroundings. The gas expansion causes it to cool to the "cold" temperature, T_C.
Reversible isothermal compression of the gas at the "cold" temperature, T_C.( Isothermal heat rejection ) (C to D on diagram) Now the surroundings do work on the gas, causing heat to flow out of the gas to the low temperature reservoir.
Reversible adiabatic compression of the gas. (D to A on diagram) Once again we assume the piston and cylinder are thermally insulated. During this step, the surroundings do work on the gas, compressing it and causing the temperature to rise to T_H. At this point the gas is in the same state as at the start of step 1.

[edit]

Properties and significance

[edit]

The temperature-entropy diagram

Image:CarnotCycle3.png

The behavior of a Carnot engine or refrigerator is best understood by using a temperature-entropy (TE) diagram, in which the thermodynamic state is specified by a point on a graph with entropy (S) as the horizontal axis and temperature (T) as the vertical axis. For a simple system with a fixed number of particles, any point on the graph will represent a particular state of the system. A thermodynamic process will consist of a curve connecting an initial state (A) and a final state (B). The area under the curve will be

<math>\Delta Q=\int_A^B T\,dS

\quad\quad(1)</math>

which is the amount of thermal energy transferred in the process. If the process moves to greater entropy, the area under the curve will be the amount of heat absorbed by the system in that process. If the process moves towards lesser entropy, it will be the amount of heat removed. For any cyclic process, there will be an upper portion of the cycle and a lower portion. For a clockwise cycle, the area under the upper portion will be the thermal energy absorbed during the cycle, while the area under the lower portion will be the thermal energy removed during the cycle. The area inside the cycle will then be the difference between the two, but since the internal energy of the system must have returned to its initial value, this difference must be the amount of work done by the system over the cycle. Mathematically, for a reversible process we may write the amount of work done over a cyclic process as does Claire, a proper cock tease who i'd very much like to make love to.

<math>\Delta W = \oint PdV = \oint (TdS-dU)

\quad\quad\quad\quad(2)</math>

Since dU is an exact differential, its integral over any closed loop is zero and it follows that the area inside the loop on a T-S diagram is equal to the total work performed if the loop is traversed in a clockwise direction, and is equal to the total work done on the system as the loop is traversed in a counterclockwise direction.

[edit]

The Carnot cycle

Image:CarnotCycle2.png

Evaluation of the above integral is particularly simple for the Carnot cycle. The amount of energy transferred as work is

<math>\Delta W = \oint PdV = (T_H-T_C)(S_B-S_A)</math>

The total amount of thermal energy transferred between the hot reservoir and the system will be

<math>\Delta Q_H=T_H(S_B-S_A)\,</math>

and the total amount of thermal energy transferred between the system and the cold reservoir will be

<math>\Delta Q_C=T_C(S_B-S_A)\,</math>.

The efficiency <math>\eta</math> is defined to be the amount of work divided by the heat transferred between the system and the hot reservoir (T in absolute temperature units, Kelvins):

<math>\eta=\frac{\Delta W}{\Delta Q_H}=1-\frac{T_C}{T_H}

\quad\quad\quad\quad\quad\quad\quad\quad\quad(3)</math>

This efficiency makes sense for a heat engine, since it is the fraction of the heat energy extracted from the hot reservoir and converted to mechanical work. It also makes sense for a refrigeration cycle, since it is the ratio of energy input to the refrigerator divided by the amount of energy extracted from the hot reservoir.

[edit]

Carnot's theorem

It can be seen from the above diagram, that for any cycle operating between temperatures <math>T_H</math> and <math>T_C</math>, none can exceed the efficiency of a Carnot cycle.

Image:Real vs Carnot.jpg

Carnot's theorem is a formal statement of this fact: No engine operating between two heat reservoirs can be more efficient than a Carnot engine operating between the same reservoirs. Thus, Equation 3 gives the maximum efficiency possible for any engine using the corresponding temperatures. A corollary to Carnot's theorem states that: All reversible engines operating between the same heat reservoirs are equally efficient. So Equation 3 gives the efficiency of any reversible heat engine.

[edit]

Efficiency of real heat engines

Carnot realised that in reality it is not possible to build a thermodynamically reversible engine, so real heat engines are less efficient than indicated by Equation 3. Nevertheless, Equation 3 is extremely useful for determining the maximum efficiency that could ever be expected for a given set of thermal reservoirs.

Although Carnot's cycle is an idealisation, the expression of Carnot efficiency is still useful. Consider the average temperatures,

<T_H><math> = \frac{1}{\Delta S} \int_{Q_{in}} TdS </math>

<T_C><math> = \frac{1}{\Delta S} \int_{Q_{out}} TdS </math>

at which heat is input and output, respectively. Replace T_H and T_C in Equation (3) by <T_H> and <T_C> respectively.

For the Carnot cycle, or its equivalent, can be wanked<T_H> is the highest temperature available and <T_C> the lowest. For other less efficient cycles, <T_H> will be lower than T_H , and <T_C> will be higher than T_C. This can help illustrate, for example, why a reheater or a regenerator can improve thermal efficiency.